BMW M2 PERFORMANCE AC sun visor strip
BMW M2 PERFORMANCE AC sun visor strip
140x20cm sun visor strip designed to fit all cars. This sticker to place on your windshield is delivered in 2 parts to superimpose ( 1 background + 1 lettering )
More information below
Product Description
Product Description
Colors and modifications
Colors and modifications
Background and marking colors can be chosen from the options above.
CHANGES
For more customization, you can contact us by email before your order. Remember to be as specific as possible so that the request is processed quickly.
Preparing the windshield
Preparing the windshield
Before you start installing your strip, make sure that your windshield is well degreased (even if the vehicle is new)
How to properly degrease your windshield?
- A good cleaning with water and NON-shine shampoo is recommended for a first pass and to remove all dirt.
- Finish with a window cleaner as you normally would. Then let dry.
WARNING: Do not use WD40, white spirit, polishing shampoo, Vulcanet wipes, etc. and other products with silicone or which could alter the glue.
Read the 3 mistakes to avoid...
OUR ADVICE +
- It is important that the support is not at too low a temperature. In winter, work preferably indoors, remember to store it there a few hours before.
- If the stickers are not applied immediately, store them in a dry place away from sunlight and heat.
- After application, avoid contact with cold and humidity for the first few days to optimize hold.
Tutorial
Tutorial
You will receive the sun visor strip in 2 parts (the background + the marking) all under flexible transfer to facilitate installation.
Preparing the stickers
- First of all, it will be necessary to distinguish each element.
- On a table, lay the marking flat, as you received it. Then pass the squeegee vigorously over this marking, in order to recapture a little of the transfer grip that could have moved during transport.
APPLICATION OF STICKERS
1. DETERMINE EACH LOCATION
Without gluing it, first place the bottom on the windshield to determine its location. You then decide the height you wish to keep. (check the law in force in your country on this subject)
Hold this final position with tape (painter's tape for example)
2. START PASTING
Once the location is decided, start by peeling off the backing paper (the bottom one) in one corner.
Spray a tiny bit of water ( no soap ) on the surface of the windshield and (optional) the sticky surface of the sticker.
Run the squeegee vigorously and methodically back and forth over the transfer, removing all air and water bubbles.
When the sticker is completely stuck, remove the transfer (semi-transparent paper) carefully, from one corner to the other, keeping it flat on the windshield. Pull back.
If in places, often at the beginning of removal, the sticker comes off, then stick it back on and press firmly again, it is because there is still too much moisture under the glue.
To optimize the hold, once the transfer is removed, you can run a hair dryer very lightly over it, this will dry the moisture quickly.
CAUTION: DO NOT HEAT A WINDSHIELD THAT IS TOO COLD, RISK OF CRACKS.
3. FINISHING AND CUTTING
Take a new blade and cut off the excess adhesive vinyl using the edge of the windshield as a guide.
Push out the last air bubbles with your finger, they may appear on the edges.
Heat a little and lightly to finish.
Repeat the operation for the marking, over this background.
OUR ADVICE +
- It is important to keep the surface at the correct temperature. A surface that is too cold will not allow the stickers to stick. In winter, work preferably indoors, and remember to heat the surface a little during installation using a heat gun.
- If the stickers are not applied immediately, store them in a dry place away from sunlight and heat.
- After application, leave to dry in a dry place at room temperature if possible. Avoid contact with cold and humidity for the first few days to optimize the hold.
VIDEO TUTORIAL
VIDEO TUTORIAL
We are installing a windshield strip, watch this video to find out more: TIKTOK VIDEO
Installation guarantee
Installation guarantee
On this product made to order, PRSmotorsport cannot guarantee a return, exchange or refund.
For this reason :
- Remember to choose your colors and model carefully to avoid any inconvenience.
- Follow our application recommendations to the letter for perfect application.
Returns and Refunds
Returns and Refunds
Windshield strips are made-to-order products.
Therefore, returns, exchanges and refunds are not possible.
It is therefore important to check your order carefully and contact us if in doubt.
Professional quality
These windshield strips are designed by cutting into mass-dyed vinyl.
Very resistant to detergents, bad weather and UV rays, does not fade unlike what can be seen on printed banners.
Application made easy by a flexible and semi-transparent transfer coating.
A 2-step application
In order to adapt to all vehicles and provide ideal positioning, these sun visor strip stickers are delivered in 2 parts.
You just need to apply the base coat first by moistening the windshield a little to make it easier to apply without bubbles. Then superimpose the marking on this base coat, dry this time.
Remember to make marks before sticking the lettering.
To facilitate positioning, the transfer is semi-transparent.